Verification Tester
TREND VDV II PRO | Cable Verifier
The VDV II performs standard tests for copper cabling, including:
- Coax, 6Pin (RJ11/12), 8Pin (RJ45) Connectors for Copper Cable Testing
- Wiremap for Miswires, Split Pairs, Shorts and Opens
- Analog Tone Generator
- Voltage Protection
- Shielded Cable Testing
- Single Screen Results
- Multimedia Support
- TDR Length Testing and Troubleshooting
- Tone Generator
- PoE Detection
- Storage and Protection of Remote Unit
- Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, UTP and STP Testing
- Large Backlit Screen
- Media Service Detection
- Ethernet Detection
- Voltage Protection
Qualification Tester
SignalTEK NT – Transmission Tester
If you install, maintain or troubleshoot data cabling and Ethernet networks, SignalTEK NT allows you to prove the performance up to Gigabit Ethernet transmission rates.
*** Now includes a touchscreen ***
- Provide proof of performance to your clients with PDF reports.
- TREND AnyWARE app – Send reports from anywhere. Click here for details.
- Network traffic performance test to IEEE802.3ab standard.
- Cable tracing – Port blink to visually trace cables.
- Displays port ID of LLDP/CDP – Eliminate manual cable tracing.
- Copper cable testing – Wiremap and distance to fault using TDR.
- Fibre cable testing – optical power indication. (SFPs required)
- PoE – Power over Ethernet verification with voltage.
Cable Installation:
Cabling:
- Network traffic performance test on copper and fibre to IEEE802.3ab standard
- Wiremap test for open, shorts, miswires and split pairs to TIA-568 standard
- Gigabit link verification for copper and fibre cabling
Active network:
-
- Network load testing through switches simulating CCTV/IPTV/VoIP/Web traffic
- PoE/PoE verification that displays available voltage at device location
- Check Ethernet connectivity at device location to 10/100/1000 Mb/s
- Verify network configuration (device IP/gateway address/subnet mask)
- Switch port identification via LLDP/CDP protocols
Certification Tester
TREND LanTEK IV | 500MHz Cable Certifier with PL Adapters
THE FUTURE OF COPPER AND FIBRE CABLE CERTIFICATION
- 7 second test time for Cat 6A
- Unique VisiLINQ™ permanent link adapters
- Certifies up to Cat 8 standards
- Measures TCL and Resistance Unbalance
- Pre-configuration eliminates setup errors
- Sapphire Care Plan minimises costs
The LanTEK IV cable certifier brings a new standard to the industry, saving you time and improving profitability. It’s time to change the way you certify.Futureproof and Fast Certifier
A copper and fibre cable certifier, it can test and save a Cat6A link in 7 seconds and certifies links up to Cat8.1 and Cat8.2, including TCL and Resistance Unbalance measurements. Plus, LanTEK IV future-proofs your investment – it will sweep to 3000MHz providing room for future ISO/TIA test standards.
VisiLINQ permanent link adapters
With unique VisiLINQ™ permanent link adapters, there is no need to even hold the certifier. Everything you need is in the palm of your hand – this is a totally new way to certify that will boost productivity.
The LanTEK IV cable certifier brings a new standard to the industry, saving you time and improving profitability. It’s time to change the way you certify.
Futureproof and Fast Certifier
A copper and fibre cable certifier, it can test and save a Cat6A link in 7 seconds and certifies links up to Cat8.1 and Cat8.2, including TCL and Resistance Unbalance measurements. Plus, LanTEK IV future-proofs your investment – it will sweep to 3000MHz providing room for future ISO/TIA test standards.
VisiLINQ permanent link adapters
With unique VisiLINQ™ permanent link adapters, there is no need to even hold the certifier. Everything you need is in the palm of your hand – this is a totally new way to certify that will boost productivity.